The generator was replaced by a built-in type and an external one. The two small boxes originally placed in the lower part of the carriage were removed, and then two metal boxes with the same dimensions of 760 mm×600 mm×600 mm were rebuilt. Firstly, the angle steel is welded into a frame, and a load-bearing belt with a width of about 50-60mm and a thickness of 3-4mm is reinforced on the front, rear and inner sides, respectively. The outer surface of the box is reinforced and welded in two directions. Steel bars with coincident generator bases, 12-15 mm thick steel plates on the bottom, other box surfaces can be made of ordinary iron or galvanized steel. The doors are integrated with open doors and the door shaft is at the bottom, on the front and rear sides. There is a lock; finally a horizontal steel strip is welded at the original hanging box of the car body and drilled. Eight short steel rods with a diameter of 10 to 12 mm are fixed on the steel frame on the box and fixed on the three steels. Bring two (original) strips, and then drill two holes at the bottom of the box with two holes corresponding to the generator. Screw the original screw cap to the load-bearing belt on the bottom of the box. Use a screw to fix the generator to prevent The generator slides when the body is moving, and the box body paint is the same color as the body. In addition, two small bearings with a diameter of 200 mm were placed outside the two steel bar seats to allow the generator to slide. The left side of the box is made in the same way as the original box cable inside the left side is placed in the left box, and the original spare tank port is changed from the inside to the back side.
After the alternator position is changed, it is faster and more convenient to take out the generator during training and save time and effort. At the same time, the free space in the passenger compartment is increased. In this way, the tent placed on the operating bed can be placed at the fixed place of the original generator, which is convenient to remove, and also avoids the damage caused by the long-term extrusion of the tent to the operating bed, and more importantly, it is Eliminate some insecure factors.
The composition and principle of the 1 SELDI system The SELDI system consists of a protein chip, a mass spectrometer, and analysis software. The design of the protein chip stems from the design method of the gene chip and the principle of biomolecular reaction.
A 1kg lead drop was added to each of the two hooks. When the winch was used to retract the wire rope, the wire rope was always in a stretched state due to the gravity of the lead sinker. When the winch is put on the rope, the steel wire rope can fall in time without being piled up; when the winch is recovered, the steel wire rope can immediately return to the groove.
It should be noted that when the top support bar of the car is moved, the lead sinker should be prevented from swinging left and right to injure or damage the car body.
Making a “Y†type attachment for the jack to take a 600mm×150mm×30mm rigid board to make a “Y†type with a wide head, a narrow tail, a smooth edge and a semi-circular head inward Device. Pay attention to the tail of the board can not be too narrow, or when the tail landing, the jack is easy to shake around; head inward arc should be consistent with the arc of the jack foot, it happens to coincide, better fixed jack. When using, hold the "Y" type device with both hands, hold the jacking head on the head, align with the fixing groove, and move the jack upwards. Then hold the tail on the ground and use the toe to hold it up. The right hand will lift the jack up or toward the jack. Rotate 180° downwards, and withdraw the “Y†device backwards. Note that the Y-type device is always parallel to the jack fixing groove during operation, otherwise the fixing bolt is not easy to rotate.
It is suggested that the steel tent structure of the surgical tent be changed to the field shower car attached to the steel tent style. We found in the usual training that the field shower attachment tent was constructed under the same environmental conditions, which saved time and effort, and had strong wind resistance. Good stability. We suggest whether the steel tent structure of the tent for surgery can be changed to the tent style for the field shower.
Cat Part,Cat Oil Filter,Engine Oil Filter,Seal Cat Oil Filter
JiLin LangYi Mechanical Equipment Company Ltd. , https://www.vxceo.com