Â
The lamella clarifier also called inclined plate sediment tank,It is kind of high efficient combined type settling tank; set many dense inclined tube packing in sediment area, to make the suspended impurity in water sediment, water rise flow along inclined tube, the separated sludge down to the tank bottom along the inclined tube by gravity, then discharge it in concentration. Such tank can improve sediment efficiency 50~60%, it can improve treatment capacity 3~5 times in the same area. It can design different flow rate inclined plate sediment device according to raw waste water test report, it need dose flocculant usually.Â
Inclined plate sediment water purifier is format by install 60° dip angle inclined tube above the sludge suspended layer, to make the suspended solids or floc alum flower by dosing flocculant accumulate into thin sludge later in inclined tube downside superficial area, slide back to sludge suspended layer rely on gravity, then settling in sludge collecting hopper, discharge into sludge tank by sludge pipe for separate treatment or comprehensive utilization. The supernatant fluid gradually rise to water collecting pipe discharge or reuse.
2. Feature:
2.1 Simple structure,without wearing parts,wear well,decrease maintenance.
2.2 Steady operation,easy operation.
2.3 Small power,save energy.
2.4 Small occupy area, low investment, high efficient.
2.5 Short retention time, high sediment efficiency, no sludge backflow.
3. Application scope
3.1 Electroplate effluent contain many kinds of metal ion, cr,cu,Fe,Zn ,Ni etc remove rate all above 90%, after treatment, all can reach discharge standard.
3.2 Coal mine,mineral processing waste water all can make the turbidity from 500-1500 mg/L reduce to 5Â mg/L.
3.3 Printing and dyeing,bleach and dye etc effluent chroma removing rate reach 70~90%,COD remove rate 50-70%.
3.4 Tannery ,food etc industrial sewage COD remove rate 50~80%, impurity solids remove rate above 90%.
3.5 Chemical waste water COD remove rate 60~70%, chroma removal rate 60~90%, suspended solids reach discharge standard.
4. Technical data:
| Specification model YMXG |
YMXG-5 | YMXG-10 | YMXG-15 | YMXG-20 | YMXG-25 | YMXG-30 | YMXG-40 | YMXG-50 |
| treatment capacity(m3/h) | 5 | 10 | 15 | 20 | 25 | 30 | 40 | 50 |
| equipment size (m) | 2.2*2*2.5 | 2.25*2.25*3.5 | 2*2.5*6 | 8*2.25*2.25 | 8*3*4.5 | 8*3.5*4.5 | 10*3.5*4.5 | 12*3.5*4.5 |
5. Structure introduction
5.1 Inclined tube material: PVC,PE,PP ,inclined plate: carbon steel lining.
5.2 Inclined tube cross section is regular hexagon, inclined plate cross section can be parallel-plate.
5.3 The cleaning water area height is 1.0-1.5m above the inclined pipe top, the water distribution zone below the bottom no less than 1.0-1.5m, mechanical discharge sludge, the water distribution zone height should more than 1.6m, convenient install and maintenance.
5.4 The Re number in water flow less than 500,Fr number is 10-3-10-5 in inclined pipe.
5.5 Inclined tube design flow rate is 1.0-4.0mm/s, inclined plate 10-20mm/s.
6.Our advantages
6.1 Material is anti-corrosion carbon steel,tinkness is 8mm,long life.
6.2 Flocculation pipe instead of flocculation tank,save space and cost.
 Contact us
| Name | Dola Li |
| Â | Â |
| Â | Â |
| Mobile phone | +86 15275216505 |
| Â | Â |
| Â Â | Â Â |
| Tel | 0532-88180456 |
| Fax | 0532-88180610 |
| Web | http:www.qingdaoyimei.cn/ |
| Address | No 386 ,Hai Bin Five Road,jiaonan, Qingdao, China |
Â
Â
The lamella clarifier also called inclined plate sediment tank,It is kind of high efficient combined type settling tank; set many dense inclined tube packing in sediment area, to make the suspended impurity in water sediment, water rise flow along inclined tube, the separated sludge down to the tank bottom along the inclined tube by gravity, then discharge it in concentration. Such tank can improve sediment efficiency 50~60%, it can improve treatment capacity 3~5 times in the same area. It can design different flow rate inclined plate sediment device according to raw waste water test report, it need dose flocculant usually.Â
Inclined plate sediment water purifier is format by install 60° dip angle inclined tube above the sludge suspended layer, to make the suspended solids or floc alum flower by dosing flocculant accumulate into thin sludge later in inclined tube downside superficial area, slide back to sludge suspended layer rely on gravity, then settling in sludge collecting hopper, discharge into sludge tank by sludge pipe for separate treatment or comprehensive utilization. The supernatant fluid gradually rise to water collecting pipe discharge or reuse.
2. Feature:
2.1 Simple structure,without wearing parts,wear well,decrease maintenance.
2.2 Steady operation,easy operation.
2.3 Small power,save energy.
2.4 Small occupy area, low investment, high efficient.
2.5 Short retention time, high sediment efficiency, no sludge backflow.
3. Application scope
3.1 Electroplate effluent contain many kinds of metal ion, cr,cu,Fe,Zn ,Ni etc remove rate all above 90%, after treatment, all can reach discharge standard.
3.2 Coal mine,mineral processing waste water all can make the turbidity from 500-1500 mg/L reduce to 5Â mg/L.
3.3 Printing and dyeing,bleach and dye etc effluent chroma removing rate reach 70~90%,COD remove rate 50-70%.
3.4 Tannery ,food etc industrial sewage COD remove rate 50~80%, impurity solids remove rate above 90%.
3.5 Chemical waste water COD remove rate 60~70%, chroma removal rate 60~90%, suspended solids reach discharge standard.
4. Technical data:
| Specification model YMXG |
YMXG-5 | YMXG-10 | YMXG-15 | YMXG-20 | YMXG-25 | YMXG-30 | YMXG-40 | YMXG-50 |
| treatment capacity(m3/h) | 5 | 10 | 15 | 20 | 25 | 30 | 40 | 50 |
| equipment size (m) | 2.2*2*2.5 | 2.25*2.25*3.5 | 2*2.5*6 | 8*2.25*2.25 | 8*3*4.5 | 8*3.5*4.5 | 10*3.5*4.5 | 12*3.5*4.5 |
5. Structure introduction
5.1 Inclined tube material: PVC,PE,PP ,inclined plate: carbon steel lining.
5.2 Inclined tube cross section is regular hexagon, inclined plate cross section can be parallel-plate.
5.3 The cleaning water area height is 1.0-1.5m above the inclined pipe top, the water distribution zone below the bottom no less than 1.0-1.5m, mechanical discharge sludge, the water distribution zone height should more than 1.6m, convenient install and maintenance.
5.4 The Re number in water flow less than 500,Fr number is 10-3-10-5 in inclined pipe.
5.5 Inclined tube design flow rate is 1.0-4.0mm/s, inclined plate 10-20mm/s.
6.Our advantages
6.1 Material is anti-corrosion carbon steel,tinkness is 8mm,long life.
6.2 Flocculation pipe instead of flocculation tank,save space and cost.
 Contact us
| Name | Dola Li |
| Â | Â |
| Â | Â |
| Mobile phone | +86 15275216505 |
| Â | Â |
| Â Â | Â Â |
| Tel | 0532-88180456 |
| Fax | 0532-88180610 |
| Web | http:www.qingdaoyimei.cn/ |
| Address | No 386 ,Hai Bin Five Road,jiaonan, Qingdao, China |
Â
Zinc Die Casting Products are a metal forming process in which molten zinc metal is put under pressure and injected into a die.
Zinc are alloys that have high strength and hardness, outstanding corrosion resistance,full recyclability, mechanical properties, high thermal and electrical conductivity and strength at high temperatures. Zinc alloys possess high dimensional stability for complex shapes and excellent thin walls. The cost of raw material is low.
Zinc Die Casting Products are efficient and economical and offers a wide range of durable shapes and components. Little or no machining is required after a part is die casted, because the process provides very close tolerances for even complex shapes. Zinc Die Castings can also be easily plated or finished. Zinc Die Casting Products are dimensionally stable and heat resistant.
Although this alloy exhibits excellent casting characteristics, it has seen limited use by die casters. It does however possess some interesting characteristics that may be of assistance to designers. Its creep performance is rated higher than the other zinc alloys and it maintains higher strength and hardness levels after long-term aging.
The behavior of zinc alloys under stress is non-linear and time-temperature dependent on strain-rate, i.e. the ratio of stress to strain is not constant, even at low stresses, and varies with time resulting in continuous plastic flow under constant applied load. Designers of structural components should be aware of the creep limitations of zinc alloys, which do not have a single value for elastic modulus or yield strength. Yield strength (allowable stress) under sustained loading is dependent on the allowable design strain (% elongation) over the required service life. Working values for the elastic modulus and yield strength are important for design purposes. Standard engineering formulae used for calculating cross-sections of elastic materials must therefore be used with some caution.
This alloy exhibits excellent damping capacity and vibration attenuation in comparison with Aluminum Die Casting alloys.
We have professionally produced Zinc Die Casting Products nearly 7 years. The parts have a great property of high quality, high precision, reasonable competetive price. our products are very popular.
Zinc Die Casting Products
Zinc Die Casting, die casting parts, Zinc Alloy Die Casting, Zinc Casting, Hardware Parts, Valve Parts, Auto Parts
NINGBO ZHENHAI BOLANG METAL PRODUCT FACTORY , http://www.bldiecasting.com